Is cantilever racking better than selective rack for tube?

For long tube bundles, usually yes: the open face removes front-column interference. Selective rack remains appropriate for palletized components that fit its openings. Compare the load's length and handling method before assigning either system.

Can loose sheet material rest directly across the arms?

Only when its support requirements allow it. Thin sheet can deflect between arms and may require a suitable support surface or carrier. Specify sheet dimensions, pack weight, and packaging rather than treating every sheet load alike.

How is capacity calculated when several arms share a bundle?

Check each arm's expected share and the total upright loading under the selected arrangement. Unequal placement can concentrate weight on fewer arms, so a simple average does not prove the configuration is suitable.

Should round stock have arm restraints?

Round stock needs a specified means of controlling rolling during storage and handling. End restraints can form part of that arrangement, but they do not replace correct load placement or increase the arm's rated capacity.

Cantilever Rack warehouse storage example

Menomonee Falls, Wisconsin

Cantilever Rack in Menomonee Falls, WI

Name: Milwaukee Pallet Rack
Address: 7311 W Greenfield Ave., Milwaukee, WI, 53214, US
Telephone: (414) 260-3593
Price range: $$

Cantilever rack in Menomonee Falls supports long components on projecting arms, with no front columns interrupting the loading face. That open frontage matters when a forklift must place an entire pipe bundle or withdraw lumber without threading it through a pallet bay. Support geometry, not nominal bay width, drives the arrangement.

For cantilever storage rack planning, begin with how each load reaches the arms. Fork position, bundle balance, and withdrawal space influence usable capacity as much as rack height. We operate as a division of Warehouse Equipment & Supplies Co., whose supply and installation work dates to 1997.

(414) 260-3593

Cantilever Rack Handling Comes First

The following checks turn a list of stock lengths into a workable handling plan, with storage dimensions tied to actual movements.

Trace the incoming load

Identify where bundles are unloaded, checked, and separated. Allow a defined transfer area before assigning the first storage face beside receiving.

Measure the lifting equipment

Record forklift capacity at the intended load center, fork spread, and lift height. Assess a side-loader separately because its carrying orientation changes aisle requirements.

Establish bearing points

Choose upright centers that support full bundles and shorter pieces. Flexible tube or lumber may require more support points than stiff bar of similar length.

Assign loading elevations

Leave room for forks and lifting clearance above each bundle. Keep frequently handled sizes at accessible levels while respecting the complete structure's load limits.

Cantilever Rack Selection and Supply Scope

Our planning sequence establishes load families, support locations, handling clearances, and then the row arrangement. Arm length follows bundle depth; arm capacity follows the actual weight distribution and specified loading condition. Upright spacing follows the material's ability to span between supports, including the shortest stock expected in that location.

Single-sided configurations can place long inventory along an edge of the storage area. Double-sided configurations serve two aisles and need both loading faces kept accessible. We compare those footprints against the available floor, not just the number of arms shown on a component list.

Tell us whether the installation is indoors, outdoors, or split between the two. Exposure and product protection affect the proposed finish and storage arrangement. The installation scope identifies the agreed rows, elevations, and component configuration so the supplied system corresponds to the reviewed load schedule.

A free CAD review displays support centers and the assembly transfer route for your approval. New rack components and installation appear as itemized scope, and we schedule experienced crews while managing the agreed installation sequence.

Compare the storage choices for your operation: Menomonee Falls storage planning; Open-arm storage overview; Falls pallet flow systems; Falls drive-in arrangements.

Tube and bar inventory

Assembly feedstock

Lumber bundles

Separated short lengths

Call (414) 260-3593

Cantilever Rack for Mixed Component Lengths

Industrial supply and light assembly around Falls Industrial Park can require several lengths of tube, bar, and extrusion beside production inventory. Those materials benefit from assigned arm levels that keep lengths visible and separated. Short remnants need their own support check rather than an assumption that any open position will work.

Along County Line Road and the Pilgrim Road corridor, a layout should distinguish long-load handling from ordinary pallet replenishment. A truck carrying projecting stock occupies a different travel envelope. We look at turns and transfer points so an open rack face does not lead directly into a conflicting movement.

Unobstructed loading faces

Separate remnant positions

Clear truck transfer space

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Industrial Supply Meets Assembly

The Mill Road industrial area and US 45 corridor connect distribution with manufacturing activity. Where long components feed assembly, position storage so retrieval does not require carrying projecting bundles through packing work.

Manufacturing

Retail distribution

Industrial components

Recent Installations

A sample of warehouse racking installations.

View More Projects

Share Your Falls Load Schedule

Provide bundle dimensions, material weights, available floor space, and equipment information. Note which products are picked as full bundles and which are broken into smaller quantities. Call (414) 260-3593.