Will a single-sided row use less room beside a wall?

It can suit that location because only one face needs loading access. However, include the base footprint, load projection and working aisle in the comparison. The visible arm depth alone does not describe the occupied space.

Can I add more levels in a low building?

Only when vertical clearance and structural capacity allow them. Closer arm elevations may prevent the truck from lifting bundles clear. Review the loaded height, lifting movement and total upright demand before adding positions.

Why choose open arms instead of selective bays?

Open arms avoid front-column interference when positioning long material. Selective bays are generally better aligned with individual pallet storage. The deciding issue is whether your load needs continuous front access or a defined pallet opening.

Can short offcuts rest across widely spaced arms?

Only if they reach the required supports with acceptable overhang. Many offcuts need a separate storage arrangement because full-length upright spacing leaves them inadequately supported. Set a minimum permitted material length for each designated position.

Cantilever Rack warehouse storage example

West Allis, Wisconsin

Cantilever Rack in West Allis, WI

Name: Milwaukee Pallet Rack
Address: 7311 W Greenfield Ave., Milwaukee, WI, 53214, US
Telephone: (414) 260-3593
Price range: $$

Cantilever rack in West Allis holds long fabrication material on open-front arms without front columns breaking up the loading face. Bar, pipe, tube, lumber and bulky sheet loads need support that follows their dimensions rather than a standard pallet opening. In an older industrial building, that support also has to fit the available approach.

A row can fit between building columns yet remain difficult to load. Draw the longest carried bundle through the aisle and into position before treating the surrounding floor as usable storage space.

(414) 260-3593

Fit Cantilever Rack to the Working Envelope

Begin with the building and vehicle path, then establish the support dimensions that the material itself requires.

Measure the obstructions

Locate building columns, doors and fixed equipment. Record available height over the full row, including the space needed to raise material off an arm.

Trace loaded movement

Use the actual forklift dimensions and longest carried load. Compare side-loader access where relevant, using its operating requirements rather than a generic aisle width.

Position the supports

Set upright spacing from stock stiffness, length and allowable overhang. Provide the required supporting surface for sheet loads that cannot rest on separated arms.

Confirm reach and rating

Choose arm length for bundle depth, then verify arm and upright capacity. Include uneven placement and the cumulative weight of loaded levels.

Cantilever Rack Within Existing Building Limits

West Allis metal fabrication and industrial supply businesses often work within older industrial layouts. Around the 70th Street industrial area and National Avenue, existing columns and limited clear height make row placement especially important. Align storage with the material route rather than forcing a long bundle through successive turns to reach an otherwise convenient wall.

Low overhead space changes the number of practical levels, not the need for proper support. Keep enough vertical clearance to lift a bundle free of its arms. Separate full lengths from shorter offcuts when the same upright spacing cannot provide adequate contact for both.

Column-aware row placement

Clearance for bundle lifting

Separate full lengths and offcuts

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Fabrication Storage in Existing Industrial Space

Along Greenfield Avenue and I-894, West Allis industrial supply operations need workable receiving routes for long material. For fabrication users, stock storage should preserve access to cutting and assembly areas rather than compete with those movements.

Metal fabrication

Industrial supply

Light assembly

Cantilever Rack Arrangements for Available Faces

Our division belongs to Warehouse Equipment & Supplies Co., a business supplying and installing warehouse storage since 1997. We plan cantilever racking around measured building constraints, stated load weights and handling equipment, making the proposed arm positions and working aisles visible before selection.

Indoor and outdoor locations should be evaluated independently. An exposed material yard needs an appropriate finish and a reviewed supporting surface, while an indoor row must work around columns, doors and production equipment. In either setting, the accessible loading face must remain reachable with the intended stock.

The free CAD layout outlines row placement and loading clearances within the existing building. An itemized new-material quote defines assembly scope, with experienced installation crews scheduled and managed around your fabrication access requirements.

Compare the storage choices for your operation: West Allis warehouse planning; Cantilever storage rack arrangements; West Allis pallet flow options; West Allis drive-in storage.

Long fabrication stock

Pipe and tube bundles

Lumber beside assembly

Supported sheet packs

Call (414) 260-3593

Recent Installations

A sample of warehouse racking installations.

View More Projects

Show Us Your West Allis Floor Plan

Include column locations, available height, load dimensions and maximum bundle weights. Add your truck model and a sketch of the route between receiving, storage and production. Call (414) 260-3593.